In this article, we will be talking about the In-wall speakers and how you can install them. In-wall speakers are designed to be installed directly into your wall, providing surround sound without the hassle of bulky floor speakers. They work by using the space inside your walls to naturally enhance the acoustics, creating a rich, full sound.
Key Features to Look for When Buying in-Wall Speakers
When choosing in-wall speakers, you’ll want to consider a few key features to ensure high-quality sound for your space.
1. Sensitivity and Power
For most rooms, look for speakers with at least 80 to 100 watts of power and a sensitivity rating of 87 decibels or higher. More power means the speakers can play louder without distortion, while higher sensitivity means they can produce more volume using less power. For larger rooms, you’ll want more power, around 150 watts or more per channel.
2. Tweeter Size
The tweeter is responsible for producing high frequencies, so a larger tweeter, 1 inch or bigger, will provide a better treble response. Soft dome tweeters also tend to produce a smoother, more natural sound than hard dome tweeters.
3. Woofer Size
A larger woofer, 6.5 to 8 inches, will provide deeper, richer bass. For small to medium rooms, a 6.5-inch woofer should work well, but bigger rooms will benefit from an 8-inch or larger woofer for impactful low end.
4. Sound Quality
Look for in-wall speakers specifically designed to provide high-fidelity sound quality for the best listening experience. Specs like a wide frequency range (60Hz to 20kHz or more), low total harmonic distortion, and premium components are good signs the speakers are made for optimal sound quality.
5. Ease of Installation
Choose in-wall speakers that will install easily into your wall space. Look for a frame size that will fit in your wall’s construction, rotatable tweeters for the best dispersion, and included mounting hardware for a secure, long-lasting installation. Brackets that allow you to fine-tune the speaker’s angle will help direct sound to your listening area.
You can buy an in-wall speaker on Amazon using the link below:
How to Install In-Wall Speakers – Step-by-Step Guide
The following are steps to install in-wall speakers:
1. Gather Your Supplies
Before getting started, make sure you have everything:
- In-wall speakers
- Speaker wire
- Wire strippers/cutters
- Drywall saw or utility knife
- Wire fish or fish tape
- Wall anchors or speaker brackets
- Screwdrivers/drill
- Patching compound (for repairing drywall)
2. Choose Your Placement
Think about how you want to position your speakers for optimal sound. In a surround sound setup, place the front left and right speakers about 6-8 feet apart and 4-6 feet high, angled towards the listening position. Side surrounds should be to the left and right sides, slightly behind the listening spot. Place the speaker wire in the walls during installation for a clean finish.
3. Cut the Holes
Use the speaker cutout template or measure the speaker size to cut holes in the drywall. Go slowly and check your measurements. It’s easier to make a hole bigger than patch a hole that’s too big! For stud walls, cut the hole so at least 2 edges contact the studs. This gives you solid material to secure the speakers too.
4. Run the Wires
Use a fish tape to guide the wire from the speaker location to your amplifier. Have someone feed the wire through as you push the fish tape in the opposite direction. Leave about 6 to 8 inches of wire hanging out each hole.
5. Mount the Speakers
Secure your speakers in the holes using the provided brackets or wall anchors. Connect the speaker wires to the matching colored terminals on the back of each speaker. Ensure the positive and negative wires don’t touch to prevent shorting out. Push any excess wire back into the wall and patch up any holes with drywall compound.
6. Test and Finish Up
Power on your amplifier and test each speaker to ensure proper operation and placement. Make any final adjustments needed to volume levels or speaker angles before patching up the drywall and cleaning up debris. Now sit back, turn up the tunes, and enjoy your new in-wall surround sound system!
READ ALSO- The Essential Review About the Sound Card 2023
Conclusion
In conclusion, the in-wall speakers are very good and help make the house attractive to people. The installation is not a hard process if you follow the step-by-step guide given in this article. Do well to always visit our website for more updates like this one. Also, drop your questions in the comment section below if you have any regarding this article.